Copyright (c) 1992-2004 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 4.10-RELEASE #0: Fri Aug  6 13:24:25 CEST 2004
    root@nb.neon1.net:/usr/src/sys/compile/M0N0WALL_GENERIC
Timecounter "i8254"  frequency 1193182 Hz
CPU: Pentium II/Pentium II Xeon/Celeron (267.27-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x652  Stepping = 2
  Features=0x183f9ff
real memory  = 201326592 (196608K bytes)
avail memory = 180363264 (176136K bytes)
Preloaded elf kernel "kernel" at 0xc0ed5000.
Preloaded mfs_root "/mfsroot" at 0xc0ed509c.
Pentium Pro MTRR support enabled
md0: Preloaded image  10485760 bytes at 0xc04d39e8
md1: Malloc disk
Using $PIR table, 8 entries at 0xc00fdef0
npx0:  $on motherboard
npx0: INT 16 interface
pcib0: on motherboard
pci0: on pcib0
pcib1: at device 1.0 on pci0
pci1: on pcib1
isab0: at device 7.0 on pci0
isa0: on isab0
atapci0: port 0xf000-0xf00f at device 7.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: port 0xe000-0xe01f at device 7.2 on pci0
pci_cfgintr_virgin: using routable PCI-only interrupt 3
pci_cfgintr: ROUTE_INTERRUPT failed.
uhci0: Could not allocate irq
device_probe_and_attach: uhci0 attach returned 6
chip1: port 0x5000-0x500f at device 7.3 on pci0
pci0: at 9.0 irq 11
xl0: <3Com 3c905-TX Fast Etherlink XL> port 0xe400-0xe43f irq 5 at device 10.0 on pci0
xl0: Ethernet address: 00:60:08:35:bb:95
miibus0: on xl0
nsphy0: on miibus0
nsphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
xl1: <3Com 3c905-TX Fast Etherlink XL> port 0xe800-0xe83f irq 7 at device 11.0 on pci0
xl1: Ethernet address: 00:60:08:a1:12:11
miibus1: on xl1
nsphy1: on miibus1
nsphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
xl2: <3Com 3c905-TX Fast Etherlink XL> port 0xec00-0xec3f irq 3 at device 12.0 on pci0
xl2: Ethernet address: 00:60:08:a1:12:3e
miibus2: on xl2
nsphy2: on miibus2
nsphy2:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pcic0: mem 0xed003000-0xed003fff irq 3 at device 13.0 on pci0
pccard0: on pcic0
orm0: at iomem 0xc0000-0xc7fff on isa0
pmtimer0 on isa0
fdc0: ready for input in output
fdc0: cmd 3 failed at out byte 1 of 3
atkbdc0: at port 0x60,0x64 on isa0
atkbd0: flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: irq 12 on atkbdc0
psm0: model IntelliMouse, device ID 3
vga0: at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 8250
sio1: configured irq 3 not in bitmap of probed irqs 0
ep0: <3Com 3C509-TPO EtherLink III> at port 0x300-0x30f irq 10 on isa0
ep0: Ethernet address 00:60:97:dd:95:8d
BRIDGE 020214 loaded
IPsec: Initialized Security Association Processing.
IP Filter: v3.4.33 initialized.  Default = block all, Logging = enabled
ad0: 7MB [246/2/32] at ata0-master PIO1
Mounting root from ufs:/dev/md0c
pccard: card inserted, slot 0
wi0 at port 0x240-0x27f irq 3 slot 0 on pccard0
wi0: 802.11 address: 00:05:5d:d9:94:9c
wi0: using RF:PRISM2.5 MAC:ISL3873
wi0: Intersil Firmware: Primary 1.00.07, Station 1.03.05
ipfw2 initialized, divert disabled, rule-based forwarding enabled, default to accept, logging disabled
DUMMYNET initialized (011031)
Limiting closed port RST response from 220 to 200 packets per second
Limiting closed port RST response from 291 to 200 packets per second$